Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
add_powerdevices_rpi_only [2020/06/06 16:48] – [Commercial Power Switches] lbrpdx | add_powerdevices_rpi_only [2021/01/05 17:56] – lbrpdx | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Add Powerdevices and Buttons to your Raspberry ====== | ====== Add Powerdevices and Buttons to your Raspberry ====== | ||
- | To keep the price down, the Raspberry Pi Baird doesn' | + | To keep the price down, the Raspberry Pi board doesn' |
If you don’t want to build your own, several popular commercial options are available. They will add a power switch to your Raspberry Pu, sometimes provide a temperature-controller fan... and add a stylish look to your board. | If you don’t want to build your own, several popular commercial options are available. They will add a power switch to your Raspberry Pu, sometimes provide a temperature-controller fan... and add a stylish look to your board. | ||
Line 25: | Line 25: | ||
Here are some commercial powerdevices that are currently supported. These offer a real power cut, that means the Raspberry is really switched off. Usually these small power devices are plugged on top of the Raspberry using it's 40 Pin header. For further install instruction use the links provided. | Here are some commercial powerdevices that are currently supported. These offer a real power cut, that means the Raspberry is really switched off. Usually these small power devices are plugged on top of the Raspberry using it's 40 Pin header. For further install instruction use the links provided. | ||
- | ^Device Name ^system.power.switch | + | Here are the values you can put as '' |
- | |ATXRaspi | + | |
- | |Mausberry Circuits | + | |
- | |Pimorini OnOffShim | + | |
- | |msldigital PiBoard r2013 |REMOTEPIBOARD_2003 | + | |
- | |msldigital PiBoard r2015 |REMOTEPIBOARD_2005 | + | |
- | |UUGear Witty Pi | + | |
- | |Retroflag Cases | + | |
- | |Argon One for RPi4 |ARGONONE | + | |
+ | ^ Device Name ^ system.power.switch | ||
+ | | ATXRaspi | ||
+ | | Mausberry Circuits | ||
+ | | Pimoroni OnOffShim | ||
+ | | msldigital PiBoard r2013 | REMOTEPIBOARD_2003 | ||
+ | | msldigital PiBoard r2015 | REMOTEPIBOARD_2005 | ||
+ | | UUGear Witty Pi | WITTYPI | ||
+ | | Retroflag Cases | RETROFLAG | ||
+ | | Retroflag Cases with button | RETROFLAG_ADV | ||
+ | | Argon One for RPi4 | ARGONONE | ||
- | ====== Simple pushbutton or switches | + | |
+ | ==== Simple pushbutton or switches ==== | ||
It is possible to add a button to turn on and turn off your BATOCERA console properly! But how? | It is possible to add a button to turn on and turn off your BATOCERA console properly! But how? | ||
Line 47: | Line 50: | ||
{{ batocera_pin56.png? | {{ batocera_pin56.png? | ||
- | to connect the switch to the Raspberry Pi GPIO, plug a PIN on the GPIO3 (physical PIN 5 above on the left) and another on the mass located just to the right on the right (physical PIN 6): | + | to connect the switch to the Raspberry Pi GPIO, plug a PIN on the GPIO3 (physical PIN 5 above on the left) and another on the mass located just to the right on the right (physical PIN 6) |
===== Activation of the switch ===== | ===== Activation of the switch ===== | ||
Line 55: | Line 58: | ||
Check in the table above what is the type of power switch you need. | Check in the table above what is the type of power switch you need. | ||
- | Then, edit the config file ’’/ | + | Then, edit the config file '' |
* For a latching switch edit batocera.conf with your preferred text editor and add '' | * For a latching switch edit batocera.conf with your preferred text editor and add '' | ||
Line 73: | Line 76: | ||
{{ 65899397-ef014600-e3b3-11e9-9465-ce7629125e19.png? | {{ 65899397-ef014600-e3b3-11e9-9465-ce7629125e19.png? | ||
+ | |||
+ | ==== Retroflag ==== | ||
+ | |||
+ | Retroflag is the manufacturer who takes focus on retro case for Raspberry Pi series and for origin looking retro game controllers. In the last years they' | ||
+ | Besides the nice looking there are **always** working buttons for power and/or reset possible. But you have to take a few steps there. | ||
+ | |||
+ | - Enable the **Safe Shutdown Switch on the PCB**! This small switch depends on the used housing, refer to the shipped manual from Retroflag how to do this. | ||
+ | - Edit '' | ||
+ | - You can edit the config file from SAMBA share with your dedicated text editor | ||
+ | - or use SSH and you can edit the config file with '' | ||
+ | - or [[add_powerdevices_rpi_only# | ||
+ | - Activate or Select the correct powerswitch '' | ||
+ | - Reboot, this will activate the Safe Shutdown feature | ||
+ | |||
+ | <WRAP center round info 80%> | ||
+ | **For the NESPi 4 case only** | ||
+ | |||
+ | You have to do an additional reboot! | ||
+ | Sorry guys, but we need to make an autoconfig behind the scenes! | ||
+ | </ | ||
+ | |||
+ | Also, for the NESPi4 case, you might experience some sluggishness using the HDD/SSD " | ||
+ | |||
+ | ==== Argon One ==== | ||
+ | |||
+ | Activate the Argon One fan by adding '' | ||
+ | |||
+ | By default, the fan starts at 55 degrees Celsius. Your can define own temperature/ | ||
+ | |||
+ | # Configuration file for Argon One Pi4 case | ||
+ | # temperatures are in Celsius | ||
+ | # fan_speed are from 0-100 percent | ||
+ | # syntax is: temp_threashold=fan_speed | ||
+ | # default is: | ||
+ | 45=0 | ||
+ | 55=10 | ||
+ | 60=55 | ||
+ | 65=100 | ||
+ | |||
+ | With this ladder, fan starts at 10% when reaching 55 degrees, and rises up to 100% when reaching 65 degrees Celsius. | ||
+ | From the vendor recommendations, |
- add_powerdevices_rpi_only.txt
- Last modified: 5 weeks ago
- by dmanlfc