Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
bluetooth_controllers_-_manual_setup [2022/02/04 05:44] – better atari | bluetooth_controllers_-_manual_setup [2023/01/11 07:19] (current) – [Pair Bluetooth Controllers - manual setup] no more blank spaces atari | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Pair Bluetooth Controllers - manual setup ====== | ====== Pair Bluetooth Controllers - manual setup ====== | ||
- | First ensure that Bluetooth is enabled on your device. | + | First ensure that Bluetooth is enabled on your device. |
Establish an [[: | Establish an [[: | ||
Line 7: | Line 7: | ||
Now you are in the Bluetooth control unit. Type following commands and confirm every single one with '' | Now you are in the Bluetooth control unit. Type following commands and confirm every single one with '' | ||
- | | + | < |
- | default-agent | + | agent on |
- | power on | + | default-agent |
- | scan on | + | power on |
+ | scan on | ||
+ | </ | ||
Now set the controller in pairing mode! This strongly depends from your [[: | Now set the controller in pairing mode! This strongly depends from your [[: | ||
Line 81: | Line 83: | ||
[CHG] Controller 90: | [CHG] Controller 90: | ||
- | ===== Blacklisting | + | ===== Batocera is automatically pairing |
- | <WRAP center round todo> | + | Some devices out there break Bluetooth protocol and are always in " |
- | Demonstration needed! | + | |
+ | To work around this, it is possible to pair to only strictly pads. Put your controller into its pairing mode and then run the following: | ||
+ | |||
+ | < | ||
+ | batocera-bluetooth trust-pad | ||
+ | </ | ||
+ | |||
+ | Batocera will explicitly only search for and connect to Bluetooth controllers. This may take a while as it methodically goes through, parses and accepts/ | ||
+ | |||
+ | < | ||
+ | [root@RPI3-BATOCERA / | ||
+ | Pairing 8BitDo M30 gamepad... | ||
+ | Trusting 8BitDo M30 gamepad... | ||
+ | [root@RPI3-BATOCERA / | ||
+ | </ | ||
+ | |||
+ | The Bluetooth controller can now be used with Batocera. | ||
+ | |||
+ | Conversely, the same can be done to connect strictly to audio devices: | ||
+ | |||
+ | < | ||
+ | batocera-bluetooth trust-audio | ||
+ | </ | ||
+ | |||
+ | --> Blacklisting a device in Batocera v33 # | ||
+ | |||
+ | <WRAP center round important> | ||
+ | The functionality of this has been supplanted by '' | ||
</ | </ | ||
Line 110: | Line 139: | ||
batocera-bluetooth unblacklist <device address> | batocera-bluetooth unblacklist <device address> | ||
</ | </ | ||
+ | |||
+ | <-- | ||
===== Using batocera-bluetooth ===== | ===== Using batocera-bluetooth ===== | ||
Line 119: | Line 150: | ||
< | < | ||
batocera-bluetooth list Print the list of currently trusted and saved Bluetooth devices. | batocera-bluetooth list Print the list of currently trusted and saved Bluetooth devices. | ||
- | batocera-bluetooth list_blacklistable | + | batocera-bluetooth trust Scan for and trust a new, randomly(?) selected device. Good luck! |
- | batocera-bluetooth trust Trust a new, randomly(?) selected device. Good luck! | + | batocera-bluetooth |
- | batocera-bluetooth | + | batocera-bluetooth |
- | batocera-bluetooth | + | batocera-bluetooth starttrust |
+ | batocera-bluetooth stoptrust | ||
batocera-bluetooth remove <device address> | batocera-bluetooth remove <device address> | ||
batocera-bluetooth save Saves the newly trusted device to memory. | batocera-bluetooth save Saves the newly trusted device to memory. | ||
batocera-bluetooth restore | batocera-bluetooth restore | ||
+ | batocera-bluetooth live_devices | ||
</ | </ | ||
+ | |||
+ | --> v33 specific commands# | ||
+ | |||
+ | < | ||
+ | batocera-bluetooth list_blacklistable | ||
+ | batocera-bluetooth blacklist <device address> <device name> | ||
+ | batocera-bluetooth unblacklist <device address> | ||
+ | </ | ||
+ | |||
+ | <-- | ||
- bluetooth_controllers_-_manual_setup.1643949890.txt.gz
- Last modified: 2 years ago
- by atari