Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Last revision Both sides next revision
devices [2020/12/01 22:24]
rtissera [Khadas VIM2]
devices [2021/03/16 14:40]
igyenes [Amlogic S905X3 based TV Boxes]
Line 105: Line 105:
 == Suggestions == == Suggestions ==
 Good for a wide range of emulators, but if you want to take it further, look at Odroid XU4 or N2. Good for a wide range of emulators, but if you want to take it further, look at Odroid XU4 or N2.
 +
 +----
 +====Odroid C4====
 +
 +== Description ==
 +
 +== Limitations ==
 +
 +== Needed Accessories ==
 +
 +== Suggestions ==
 +Good for a wide range of emulators, this board provides performance close to Raspberry Pi 4.
  
 ---- ----
Line 140: Line 152:
 ---- ----
 {{ :odroidgoa.jpg?200|}} {{ :odroidgoa.jpg?200|}}
-====Odroid Go Advance====+====Odroid Go Advance / Super====
  
 == Description == == Description ==
-Available in two variants: original Odroid Go Advance (launched in January 2020) and Odroid Go Advance Black Edition (launched in June 2020, which provides a USB-C power connector, integrated wifi, and two smallish R2/L2 additional buttons).+Available in several variants:  
 +  * original Odroid Go Advance launched in January 2020 
 +  * Odroid Go Advance Black Edition launched in June 2020, which provides a USB-C power connector, integrated wifi, and two smallish R2/L2 additional buttons 
 +  * Odroid Go Super - launched in January 2021, with a larger 5" screen, two analog controllers, dedicated volume buttons (but no integrated wifi any more)
  
 There are other handheld "clones" of the Odroid Go Advance available on the market, powered by the same SoC, that are fully compatible with the same Batocera build, like RK2020 and Anbernic RG351P. There are other handheld "clones" of the Odroid Go Advance available on the market, powered by the same SoC, that are fully compatible with the same Batocera build, like RK2020 and Anbernic RG351P.
  
 == Limitations == == Limitations ==
-  * If you want to use wifi and/or bluetooth on the original Odroid Go Advance, you must add a dongle that provide the two at same time because there is only one USB port. [[wiki:compatible_dongle_list|Compatible Dongles list]]+  * If you want to use wifi and/or bluetooth on the original Odroid Go Advance, you must add a dongle that provide the two at same time because there is only one USB port. [[hardware:compatible_dongle_list|Compatible Dongles list]]
  
 == Needed Accessories == == Needed Accessories ==
   * SD Card   * SD Card
-  * WIFI USB Dongle (To add internet for original OGA) +  * WIFI USB Dongle (To add internet for original OGA or OGS
-  * Bluetooth USB Dongle (for multiplayer for Original OGA)+  * Bluetooth USB Dongle (for multiplayer for Original OGA or OGS)
  
 == Suggestions == == Suggestions ==
Line 211: Line 226:
  
 To change resolution, edit /boot/extlinux/extlinux.conf. To change resolution, edit /boot/extlinux/extlinux.conf.
 +----
 +====Amlogic S905 based TV Boxes====
 +== Description ==
 +Amlogic GXBB/GXL family boxes featuring Quad Core 64bit Cortex-A53 cpu and MALI-450 GPU.
  
 +Support available in Batocera.linux **30.0** with mainline linux kernel. 
 +
 +For compatibility information, check https://batocera.org/compatibility .
 +
 +== Tested Devices ==
 +There are a wide range of devices available on the market with various wifi/lan/bt chipsets. 
 +If you have tested a device please report back the results on Discord. 
 +
 +The following devices are tested:
 +^ Model/Make     ^ LAN    ^ Wifi  ^ Bluetooth          ^ Tested DTB                ^
 +| Tanix TX3 Max  | Works  | Works | N/A (use a dongle) |meson-gxl-s905x-p212.dtb   |
 +
 +
 +== Limitations ==
 +At the time of writing:
 +  * Video splash is disabled
 +  * Shutdown may not work (reboots the system)
 +  * If your bluetooth or wifi is not working you can add a compatible dongle. [[hardware:compatible_dongle_list|Compatible Dongles list]]
 +
 +== Needed Accessories ==
 +  * SD Card or USB stick
 +
 +== Suggestions ==
 +You have to use a device specific .dtb in the FDT section of **uEnv.txt** file which is located on the root of your SD card.\\  
 +There are some dtb-s included in /boot, so if one does not work it is safe to try out another.\\ 
 +On the first boot you may have to keep pressing the reset for a few seconds. It is usually located under a small hole on the bottom of the box, or inside of the 3.5 audio jack connector. In this case you can use a toothpick to press the button.\\ 
 +Please do not use dtb-s from other sources (older Batocera.linux versions or from other distributions) as they will not work.
 +----
 +====Amlogic S905X3 based TV Boxes====
 +
 +**THIS ARTICLE IS WIP!**
 +
 +== Description ==
 +Amlogic SM1 family boxes featuring Quad Core 64bit Cortex-A55 cpu and MALI-G31 GPU.
 +
 +Support will be available in Batocera.linux **31.0**. 
 +
 +<WRAP center round important 70%>
 +There is a kernel/u-boot bug that may cause strange colors. There is no fix for that yet but for a workaround do the following:\\
 +Depending on the media you should copy the u-boot.sd or u-boot.usb file to uboot.ext and reboot. 
 +</WRAP>
 + 
 +== Tested Devices ==
 +There are a wide range of s905x3 based devices are available on the market with various wifi/lan/bt chipsets. 
 +If you have tested a device please report back the results on Discord. 
 +HK1BOX / VONATAR x3 / H96 max devices known to be the same and know to be work so this is a recommended one to start to play with.
 +
 +The following devices are tested:
 +^ Model/Make        ^ LAN    ^ Wifi   ^ Bluetooth  ^ Tested DTB                ^
 +| Vontar X3         | Works  | Works  | Works      | meson-sm1-h96-max.dtb     |
 +| X96 Air 4GB/32GB  | Works  | N/A    | N/A        | meson-sm1-x96-air-4g.dtb  |
 +
 +== Limitations ==
 +At the time of writing:
 +  * Shutdown/reboot may not work 
 +  
 +== Needed Accessories ==
 +  * SD Card or USB stick
 +
 +== Suggestions ==
 +You have to use a device specific .dtb in the FDT section of **uEnv.txt** file which is located on the root of your SD card.\\  
 +There are some dtb-s included in /boot, so if one does not work it is safe to try out another.\\ 
 +On the first boot you may have to keep pressing the reset for a few seconds. It is usually located under a small hole on the bottom of the box, or inside of the 3.5 audio jack connector. In this case you can use a toothpick to press the button.\\ 
 +Please do not use dtb-s from other sources as they will not work.
 ---- ----
 {{ :tkb.jpg?200|}} {{ :tkb.jpg?200|}}
Line 223: Line 306:
   * MQmaker MiQi   * MQmaker MiQi
   * Amlogic S905 and variants   * Amlogic S905 and variants
-  * Odroid C4 
  
  
  • devices.txt
  • Last modified: 5 weeks ago
  • by joinski