Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
devices [2021/01/30 18:57] 150.95.142.190 ↷ Links adapted because of a move operation |
devices [2021/04/11 11:14] (current) joinski |
||
---|---|---|---|
Line 6: | Line 6: | ||
And see [[choose_a_board|How to choose a board]]. | And see [[choose_a_board|How to choose a board]]. | ||
- | Finally, if you are looking to purchase a new board, the best is fist to check the available emulators for each of them [[https:// | + | Finally, if you are looking to purchase a new board, the best is fist to check the available emulators for each of them [[https:// |
---- | ---- | ||
Line 226: | Line 226: | ||
To change resolution, edit / | To change resolution, edit / | ||
+ | ---- | ||
+ | ====Amlogic S905 based TV Boxes==== | ||
+ | == Description == | ||
+ | Amlogic GXBB/GXL family boxes featuring Quad Core 64bit Cortex-A53 cpu and MALI-450 GPU. | ||
+ | Support available in Batocera.linux **30.0** with mainline linux kernel. | ||
+ | |||
+ | For compatibility information, | ||
+ | |||
+ | == Tested Devices == | ||
+ | There are a wide range of devices available on the market with various wifi/lan/bt chipsets. | ||
+ | If you have tested a device please report back the results on Discord. | ||
+ | |||
+ | The following devices are tested: | ||
+ | ^ Model/ | ||
+ | | Tanix TX3 Max | Works | Works | N/A (use a dongle) |meson-gxl-s905x-p212.dtb | ||
+ | |||
+ | |||
+ | == Limitations == | ||
+ | At the time of writing: | ||
+ | * Video splash is disabled | ||
+ | * Shutdown may not work (reboots the system) | ||
+ | * If your bluetooth or wifi is not working you can add a compatible dongle. [[hardware: | ||
+ | |||
+ | == Needed Accessories == | ||
+ | * SD Card or USB stick | ||
+ | |||
+ | == Suggestions == | ||
+ | You have to use a device specific .dtb in the FDT section of **uEnv.txt** file which is located on the root of your SD card.\\ | ||
+ | There are some dtb-s included in /boot, so if one does not work it is safe to try out another.\\ | ||
+ | On the first boot you may have to keep pressing the reset for a few seconds. It is usually located under a small hole on the bottom of the box, or inside of the 3.5 audio jack connector. In this case you can use a toothpick to press the button.\\ | ||
+ | Please do not use dtb-s from other sources (older Batocera.linux versions or from other distributions) as they will not work. | ||
+ | ---- | ||
+ | ====Amlogic S905X3 based TV Boxes==== | ||
+ | |||
+ | **THIS ARTICLE IS WIP!** | ||
+ | |||
+ | == Description == | ||
+ | Amlogic SM1 family boxes featuring Quad Core 64bit Cortex-A55 cpu and MALI-G31 GPU. | ||
+ | |||
+ | Support will be available in Batocera.linux **31.0**. | ||
+ | |||
+ | <WRAP center round important 70%> | ||
+ | There is a kernel/ | ||
+ | Depending on the media you should copy the u-boot.sd or u-boot.usb file to uboot.ext and reboot. | ||
+ | </ | ||
+ | |||
+ | == Tested Devices == | ||
+ | There are a wide range of s905x3 based devices are available on the market with various wifi/lan/bt chipsets. | ||
+ | If you have tested a device please report back the results on Discord. | ||
+ | HK1BOX / VONATAR x3 / H96 max devices known to be the same and know to be work so this is a recommended one to start to play with. | ||
+ | |||
+ | The following devices are tested: | ||
+ | ^ Model/ | ||
+ | | Vontar X3 | Works | Works | Works | meson-sm1-h96-max.dtb | ||
+ | | X96 Air 4GB/ | ||
+ | |||
+ | == Limitations == | ||
+ | At the time of writing: | ||
+ | * Shutdown/ | ||
+ | | ||
+ | == Needed Accessories == | ||
+ | * SD Card or USB stick | ||
+ | |||
+ | == Suggestions == | ||
+ | You have to use a device specific .dtb in the FDT section of **uEnv.txt** file which is located on the root of your SD card.\\ | ||
+ | There are some dtb-s included in /boot, so if one does not work it is safe to try out another.\\ | ||
+ | On the first boot you may have to keep pressing the reset for a few seconds. It is usually located under a small hole on the bottom of the box, or inside of the 3.5 audio jack connector. In this case you can use a toothpick to press the button.\\ | ||
+ | Please do not use dtb-s from other sources as they will not work. | ||
---- | ---- | ||
{{ : | {{ : |
- devices.1612029467.txt.gz
- Last modified: 3 months ago
- by 150.95.142.190