Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
supported_hardware [2020/10/17 04:27]
lbrpdx [Nvidia drivers]
supported_hardware [2021/01/22 00:15]
lbrpdx [Nvidia drivers]
Line 3: Line 3:
  
 ==== Nano computers / Single-board computers ==== ==== Nano computers / Single-board computers ====
 +Batocera supports multiple single-board computers (SBC):
 +
   * Raspberry Pi Zero   * Raspberry Pi Zero
   * Raspberry Pi (aka 1), including RetroFlag GPi Case   * Raspberry Pi (aka 1), including RetroFlag GPi Case
   * Raspberry Pi 2   * Raspberry Pi 2
-  * Raspberry Pi 3+  * Raspberry Pi 3, as well as CM3
   * Raspberry Pi 4   * Raspberry Pi 4
   * Odroid C2   * Odroid C2
 +  * Odroid C4
   * Odroid XU3, XU4, XU4Q   * Odroid XU3, XU4, XU4Q
-  * Odroid N2+  * Odroid N2 and N2+
   * Odroid Go Advance   * Odroid Go Advance
 +  * RK2020
 +  * Abernic RG351P
   * RockPro64   * RockPro64
   * Asus Tinkerboard   * Asus Tinkerboard
   * MQmaker MiQi   * MQmaker MiQi
   * Amlogic S905 and variants   * Amlogic S905 and variants
 +  * Khadas VIM2
 +  * Khadas VIM3
 +  * Libretech H5
  
 You can download the last stable version for each of these SBCs from [[https://batocera.org/download|the download section of the website]]. You can download the last stable version for each of these SBCs from [[https://batocera.org/download|the download section of the website]].
Line 41: Line 49:
    nvidia-driver=true    nvidia-driver=true
  
-You can find the list of supported GPU models in https://www.nvidia.com/Download/driverResults.aspx/141847/en-us.+You can find the list of supported GPU models in https://www.nvidia.com/Download/driverResults.aspx/168347/en-us (version 460.32.03 embedded in Batocera 30) .
  
 If you edit the file under Windows, make sure you have an editor that respects Unix line terminators. Don't use Wordpad, use a **real** text editor like Notepad++ or Atom, that doesn't replace the Unix line terminations (LF) by DOS/Windows line terminations (CR/LF). If you edit the file under Windows, make sure you have an editor that respects Unix line terminators. Don't use Wordpad, use a **real** text editor like Notepad++ or Atom, that doesn't replace the Unix line terminations (LF) by DOS/Windows line terminations (CR/LF).
 +
 +You can connect to [[access_the_batocera_via_ssh|Batocera through SSH]], remount the ''/boot'' partition on write mode [[modify_the_system_while_it_s_running|like explained here]], and edit ''/boot/batocera-boot.conf'' with nano or vi as text editors.
  
 If your card is not supported by the current branch, please check the following forum thread https://forum.batocera.org/d/1851-batoceralinux-525-with-nvidia-legacy-drivers-390xx-discontinued If your card is not supported by the current branch, please check the following forum thread https://forum.batocera.org/d/1851-batoceralinux-525-with-nvidia-legacy-drivers-390xx-discontinued
  • supported_hardware.txt
  • Last modified: 3 months ago
  • by lbrpdx